産業オートメーション部品
世界配送対応のCNC・産業オートメーション部品をご覧ください。
製品を検索
カテゴリー
Mitsubishi SCJ2SJ4PWBK1C03MA1 Motor-Side Servo Power Conversion Cable for HC-KFS/HG-KR
SKU: SCJ2SJ4PWBK1C03MA1
The Mitsubishi SCJ2SJ4PWBK1C03MA1 is a servo power conversion cable set for motor-side power and brake wiring in Mitsubishi MELSERVO servo systems. It is a 30 cm load-side cable assembly supplied with a servo amplifier connector and a servomotor connector, and it is listed as a motor-side power conversion cable with a load-side brake conductor. The pre-terminated cable is used to connect the servo drive to the motor in compact layouts and is associated with Mitsubishi renewal kits for HC-KFS and HC-MFS motors and the corresponding HG-KR and HG-MR series. It therefore suits servo-axis renewal and replacement work where the power and brake cable must be matched to the amplifier and motor connectors. Users should confirm the connector arrangement and brake conductor requirements for the specific amplifier and motor pair. The cable is intended for Mitsubishi servo-driven machinery and renewal-kit installations, with the 30 cm length helping with close-coupled drive-to-motor arrangements.
Mitsubishi SCJ2SJ4PWBK1C03MA2 Servo Power Conversion Cable for HC-KFS/HC-MFS/HG-KR/HG-MR Motors
SKU: SCJ2SJ4PWBK1C03MA2
The Mitsubishi SCJ2SJ4PWBK1C03MA2 servo power conversion cable is a 30 cm motor-side cable set for connecting a Mitsubishi servomotor to its servo amplifier. It is fitted with a servo amplifier connector and a servomotor connector, with the cable exit arranged for the opposite side of the load. Mitsubishi lists this cable in renewal kits for HC-KFS, HC-MFS, HG-KR, and HG-MR servomotors in MELSERVO servo systems, where it supports motor power wiring during replacement or service. Its compact length is useful where the amplifier and motor are mounted close together, and the pre-terminated connectors simplify installation and reduce wiring errors. The cable carries Mitsubishi material number 271235 and weighs approximately 0.136 kg. Typical applications include servo axis repair and renewal in compact machinery, replacement of damaged motor power leads, and maintenance of Mitsubishi servo systems using the listed motor families.
Mitsubishi SD-N21 32A 3-Pole Magnetic Contactor 24V DC 2NO+2NC for MS-N Series
SKU: SD-N21
The Mitsubishi SD-N21 (SD-N21) is a 32A, 3-pole magnetic contactor from the MS-N series, intended for Direct-On-Line (DOL) and full-voltage non-reversing motor starting. It has a 24Vdc control coil and two normally open plus two normally closed auxiliary contacts for status, interlock, and control circuits. The contactor is UL listed and rated for 32A and 10HP at 480Vac three-phase, so it can switch motors, pumps, fans, conveyors, and other three-phase loads in control panels. Screw-clamp terminals with finger-protection covers simplify wiring, and DIN-rail or surface mounting with a 63mm frame width helps fit compact enclosures. The SD-N21 uses the N21 frame size and is designed for MS-N series contactor applications. It is a standard, non-reversing contactor for industrial motor-control circuits that require reliable DC coil operation.
Mitsubishi SD-N220-DC24V Magnetic Contactor 24 V DC Coil for MS-N Series
SKU: SD-N220-DC24V
The Mitsubishi SD-N220-DC24V is a three-pole magnetic contactor from the MS-N series for direct-on-line (DOL) and full-voltage non-reversing motor control. Its 24 V DC control coil allows switching from a DC control circuit, while the main contacts are rated 260 A UL and 150 hp at 480 V AC in three-phase UL applications; the product data also lists a 132 kW rating. The contactor provides two normally open and two normally closed auxiliary contacts for holding, interlocking, and status circuits. Mechanical lug terminals and surface mounting simplify installation in control panels, and the 138 mm wide by 204 mm high frame has an IP20 protection class. Typical uses include motor control centers, machine tools, pumps, fans, conveyors, and other three-phase equipment that requires reliable remote starting and stopping. The SD-N220-DC24V is intended for MS-N series contactor applications requiring a 24 V DC coil and a 2NO+2NC auxiliary contact set.
Mitsubishi SD-Q11DC24V DC Interface Contactor 24 VDC 4 kW 1NO for PLC Transistor Output
SKU: SD-Q11DC24V
The Mitsubishi SD-Q11DC24V (SD-Q11DC24V) is a compact DC interface contactor from the SD-Q series, designed to be driven directly by a 24 VDC, 1 A transistor output from Mitsubishi PLCs and compatible control systems. Its DC-operated coil lets the contactor be switched without an additional interposing relay, simplifying control-panel wiring in PLC-driven motor circuits. The three-pole contactor is rated 9 A and delivers 3 kW at 220–240 V AC or 4 kW at 380–440 V AC, with one normally open auxiliary contact for signaling or interlocking. Screw-clamp terminals, 50/60 Hz operation, an ambient temperature range of -10 to 40 °C, and IP20 protection make it suitable for use inside standard industrial control cabinets. The compact housing measures approximately 45 x 51 x 66.5 mm, helping save panel space in dense installations. Typical applications include motor starting and load switching in machine tools, packaging equipment, material-handling systems, and other automated machinery where a PLC output must operate a contactor directly. It is a practical replacement for SD-Q series contactor positions requiring a 24 VDC coil and 4 kW rating.
Mitsubishi SD-Q19-DC24V DC Interface Contactor for PLC Transistor Output Control
SKU: SD-Q19-DC24V
The Mitsubishi SD-Q19-DC24V (SD-Q19-DC24V) is a compact DC-operated interface contactor in the SD-Q series, designed to be driven directly by a 24 V DC transistor output from a programmable logic controller or similar control device. It has three main poles and 1NO+1NC auxiliary contacts, with a 24 V DC coil, and is intended for panel builders who need contactor switching without a separate interface relay. The SD-Q19 version uses an efficient electromagnet with a permanent magnet; its coil operating current is 75 mA (1.8 W), allowing direct drive from a 24 V DC, 0.1 A transistor output. A built-in surge absorber limits coil surge voltage, while twin auxiliary contacts and a terminal cover support reliable switching and safer maintenance. The contactor can be mounted on 35 mm DIN rail or by screw fixing and is suited to circuit interruption, heater switching, motor starters, and reversing contactor arrangements used with thermal overload relays. It is a practical spare for Mitsubishi SD-Q series control panels and PLC-driven switching circuits.
Mitsubishi SD-T100-DC24V Magnetic Contactor 55 kW 2NO+2NC 24 V DC Coil for MS-T Series
SKU: SD-T100-DC24V
The Mitsubishi SD-T100-DC24V is a 55 kW magnetic contactor from the MS-T series, configured as a non-reversing, DC-operated three-pole device. Its 24 V DC coil and 2NO+2NC auxiliary contacts make it suitable for motor starting and stopping, direct-on-line control, and switching power circuits in control panels and machinery. At 380-440 V AC in AC-3 duty it is rated 55 kW and 105 A, with a rated operating voltage of 690 V and rated impulse withstand voltage of 6 kV. The contactor also supports 50/60 Hz systems and has a frame size 100, screw terminals, and an ambient operating range of -10 to 40 °C. Its dimensions are approximately 100 mm wide, 134 mm high, and 157 mm deep, with a net weight of about 3 kg. Typical uses include pump, fan, conveyor, and compressor motor control where a compact 55 kW contactor with a 24 V DC control coil is required.
Mitsubishi SD-T12-DC24V-1A1B Magnetic Contactor for MS-T Series
SKU: SD-T12-DC24V-1A1B
The Mitsubishi SD-T12-DC24V-1A1B (SD-T12-DC24V-1A1B) is a magnetic contactor from the MS-T series, T12 frame size, with a 24 V DC control coil and a non-reversing, direct-on-line design. It is used in low-voltage motor control panels and full-voltage non-reversing motor starter circuits to switch three-phase loads. The contactor has 3 poles, 1 normally open and 1 normally closed auxiliary contact, and screw-clamp terminals with finger protection. Its ratings include 12 A at 380-440 V AC-3 and 5.5 kW at 440 V AC-3 (IEC), with a rated operating voltage of 690 V and rated impulse withstand voltage of 6 kV. It supports 50/60 Hz systems, mounts on DIN rail or a flat surface, and is rated IP20. The compact unit measures 43 mm wide, 75 mm high, and 100 mm deep, with a net weight of about 0.42 kg. Typical uses include direct-on-line motor starting, motor starter assemblies, and other three-phase load switching in control cabinets.
Mitsubishi SD-T12-DC48V-1A1B Magnetic Contactor for MS-T Series 5.5 kW 3-Pole 48V DC
SKU: SD-T12-DC48V-1A1B
The Mitsubishi SD-T12-DC48V-1A1B (SD-T12-DC48V-1A1B) is a 3-pole magnetic contactor from the MS-T series, T12 frame, designed for direct-on-line (DOL) and full-voltage non-reversing motor control. Its 48 V DC operating coil has polarity, with A1 connected to positive and A2 to negative. The contactor is rated 12 A in AC-3 duty at 380 to 440 V AC and 5.5 kW at 440 V AC, and it includes one normally open and one normally closed auxiliary contact. Screw-clamp terminals with finger protection, IP20 protection, and DIN-rail or surface mounting support installation in control cabinets. The compact body measures 43 mm wide, 75 mm high, and 100 mm deep and weighs 0.42 kg. It is used for starting and stopping three-phase motors in pumps, fans, conveyors, compressors, and general machine-control panels, where a 48 V DC control circuit is required. The contactor is RoHS-compliant.
Mitsubishi SD-T20-DC24V-1A1B Magnetic Contactor for MS-T Series 24V DC Coil
SKU: SD-T20-DC24V-1A1B
The Mitsubishi SD-T20-DC24V-1A1B (SD-T20-DC24V-1A1B) is a 3-pole magnetic contactor from the MS-T series, designed for direct-on-line (DOL) and full-voltage non-reversing motor control. Its 24 V DC operating coil allows it to be switched from DC control circuits, while the T20 frame provides a rated current of 18 A in AC-3 duty at 380, 400, 415, and 440 V AC and a rated active power of 7.5 kW at 440 V AC according to IEC. The contactor has a rated operating voltage of 690 V and a rated impulse withstand voltage of 6 kV. The device includes one normally open and one normally closed auxiliary contact, plus screw-clamp terminals with finger protection. It is rated IP20, measures 43 mm in width, and can be mounted on DIN rail or directly on a surface. Typical uses include starting and stopping three-phase motors in pumps, fans, conveyors, compressors, and machine tools, as well as switching in low-voltage control panels. The SD-T20-DC24V-1A1B is suited to MS-T series installations that require a DC-operated contactor with auxiliary signaling contacts.
Mitsubishi SD-T20-DC48V-1A1B 3-Pole Magnetic Contactor for MS-T Series 48 V DC 7.5 kW
SKU: SD-T20-DC48V-1A1B
The Mitsubishi SD-T20-DC48V-1A1B is a three-pole magnetic contactor from the MS-T series in the T20 frame size, designed for direct-on-line (DOL) and full-voltage non-reversing motor control. It uses a 48 V DC control coil and provides one normally open plus one normally closed auxiliary contact (1NO+1NC). At 440 V AC in AC-3 duty, the contactor is rated for 7.5 kW, with an 18 A rated current at 380 V, 400 V, 415 V and 440 V AC. Its rated operational voltage is 690 V AC and its rated impulse withstand voltage is 6 kV. Screw-clamp connections with finger protection, IP20 protection and DIN-rail or surface mounting make it suitable for installation in control cabinets. The compact 43 mm width, 75 mm height and 100 mm depth help with dense panel layouts. Typical applications include direct-on-line starting and stopping of three-phase motors, pumps, fans and other machine loads controlled through Mitsubishi MS-T series contactor assemblies.
Mitsubishi SD-T21 DC24V 2A2B Magnetic Contactor for MS-T Series 287527
SKU: SD-T21-DC24V-2A2B
The Mitsubishi 287527 (SD-T21 DC24V 2A2B) is a 3-pole magnetic contactor from the MS-T series, designed for direct-on-line (DOL) and full-voltage non-reversing motor control. It uses a 24 V DC operating coil and includes 2 normally open plus 2 normally closed auxiliary contacts (2NO+2NC), making it suitable for switching three-phase motors and related control circuits in industrial machinery. The contactor is rated 11 kW at 440 V AC in AC-3 duty, with a rated operational voltage of 690 V and rated current of 23 A at 380-440 V AC-3. Screw-clamp terminals with finger protection simplify wiring, while the compact T21 frame measures 63 mm wide, 81 mm high and 108 mm deep and weighs approximately 0.594 kg. It can be combined with compatible MS-T series accessories such as TH-T25KP thermal overload relays and side- or front-mounted auxiliary contact blocks for expanded control and protection. Typical uses include motor starters, pumps, fans, conveyors and other three-phase loads in control panels and machines that require reliable DC-coil switching.
Mitsubishi SD-T21-DC48V-2A2B 3-Pole Magnetic Contactor for MS-T Series Motor Control
SKU: SD-T21-DC48V-2A2B
The Mitsubishi SD-T21-DC48V-2A2B is a 3-pole magnetic contactor from the MS-T series, designed for direct-on-line (DOL) and full-voltage non-reversing (FVNR) motor control. It uses a 48 Vdc operating coil and has 2NO+2NC auxiliary contacts. The direct-current coil is intended for control circuits that provide 48 Vdc. In AC-3 service the contactor is rated 23 A at 380-440 V AC and 11 kW at 440 V AC, with a rated operating voltage of 690 V and a rated impulse withstand voltage of 6 kV. Screw-clamp terminals with finger protection simplify wiring, and the unit has an IP20 protection class. Its dimensions are 63 mm wide, 81 mm high and 108 mm deep, with a net weight of 0.545 kg. Typical applications include starting and stopping motors in pumps, fans, conveyors and other machine-control installations.
Mitsubishi SD-T32-DC24V Magnetic Contactor for MS-T Series 15 kW 24 V DC Coil
SKU: SD-T32-DC24V
The Mitsubishi SD-T32-DC24V (SD-T32-DC24V) is a three-pole, non-reversing magnetic contactor from the MS-T series, designed for direct-on-line motor switching and full-voltage non-reversing control. Its 24 V DC operating coil allows direct drive from a transistor output, while the contactor is rated for 32 A in AC-3 duty at 380-440 V AC and 15 kW at 440 V AC (IEC). UL ratings include 20 HP at 440-480 V AC, three-phase. The contactor uses screw-clamp wiring, is suitable for 50/60 Hz supplies and has a 690 V rated operating voltage. Its compact frame measures approximately 43 mm wide by 81 mm high by 108 mm deep and weighs about 0.55 kg. Typical applications include direct-on-line motor control, full-voltage non-reversing switching, and control-panel circuits where a 24 V DC coil can be driven from a PLC transistor output.
Mitsubishi SD-T35 DC24V Magnetic Contactor for MS-T Series SD-T35-DC24V
SKU: SD-T35-DC24V
The Mitsubishi SD-T35-DC24V (SD-T35 DC24V) is a non-reversing, DC-operated magnetic contactor from the MS-T series. It has a 3-pole main contact arrangement, a 24 V DC operating coil, and 2NO plus 2NC auxiliary contacts. The contactor is rated for 18.5 kW applications and for a rated current of 17 A at 3-phase AC 690 V. Its dimensions are approximately 75 mm wide, 89 mm high, and 123 mm deep, and it weighs 0.887 kg. The unit is RoHS compliant and is supplied with a terminal cover as standard. It supports DIN-rail mounting and screw mounting. As the successor to the SD-N35, it is designed for direct full-voltage DC coil operation, where the coil resistance limits current and helps provide stable operation without high inrush current. Typical uses include switching and control of motor circuits and other loads in control panels and machine electrical systems.
Mitsubishi SD-T50-DC24V Magnetic Contactor for MS-T Series 22 kW 24 VDC
SKU: SD-T50-DC24V
The Mitsubishi SD-T50-DC24V is a three-pole magnetic contactor from the MS-T series, T50 frame size, designed for direct-on-line (DOL) and full-voltage non-reversing (FVNR) motor control. It combines a 24 VDC operating coil with two normally open and two normally closed auxiliary contacts, making it suitable for control circuits that require reliable switching of three-phase loads. At AC-3 duty, it is rated for 48 A at 380-440 V AC and 22 kW at 440 V AC; the 690 V AC rated operational voltage and 6 kV impulse withstand voltage support low-voltage motor starter applications. Screw-clamp terminals provide wiring connections. Its net weight is approximately 0.935 kg. Typical use includes motor control panels, low-voltage power distribution, and machine control systems that use the MS-T series. It is a component for starting and stopping motors, not a complete starter.
Mitsubishi SD-T65-DC24V Magnetic Contactor for MS-T Series 30 kW 2NO+2NC DC 24V Coil
SKU: SD-T65-DC24V
The Mitsubishi SD-T65-DC24V is a 30 kW magnetic contactor from the MS-T series, designed for non-reversing, DC-operated motor control. It uses a 24 V DC operating coil and has three main poles, with a rated operational voltage of 690 V AC and a rated current of 38 A at 690 V AC. Its rated motor capacity is 18.5 kW at 220-240 V AC and 30 kW at 380-440 V AC and 690 V AC, with a 50/60 Hz frequency range. The contactor includes two normally open and two normally closed auxiliary contacts for control and interlocking circuits. Screw terminals, an IP20 protection rating, and an ambient operating range of -10 to 40 °C suit it for installation in electrical control panels. The 133 mm width helps with layout in compact enclosures. Typical uses include starting and stopping three-phase motors, pumps, fans, compressors, conveyors, and other AC loads in machine and process control systems. The material number is 298638.
Mitsubishi SD-T80-DC24V Magnetic Contactor for MS-T Series 298646
SKU: SD-T80-DC24V
The Mitsubishi 298646 (SD-T80-DC24V) is a three-pole, non-reversing magnetic contactor from the MS-T series. It is designed for DC-operated control with a 24 V DC coil and provides a 45 kW rating at 380-440 V AC in AC-3 duty, along with 2 NO and 2 NC auxiliary contacts for control and interlocking circuits. The contactor has a rated operational voltage of 690 V, a rated impulse voltage of 6 kV, and screw-clamp terminals with finger protection. It can be mounted on DIN rail or on a flat surface, measures 88 x 106 x 133 mm, and weighs approximately 2.1 kg. This MS-T series contactor is used for direct-on-line and full-voltage non-reversing starting and control of three-phase motors in industrial control panels, machine tools, and motor-driven equipment. It is compatible with TH-T65KP overload relays specified for S(D)-T65, S(D)-T80, and S(D)-T100 contactors, allowing a compact motor starter assembly. The 24 V DC coil suits control systems that use a DC control bus, while the 2NO+2NC auxiliary contacts support status feedback, sealing, and interlock functions. The device is rated for 50/60 Hz operation and an ambient temperature range of -10 to 40°C.
Mitsubishi SDHC-CARD-16GB PCB Board
SKU: SDHC-CARD-16GB
Scheda di memoria MicroSDHC 16 GigaByte; Classe 10; Lettura/Scrittura: 10 MegaByte al secondo; adattatore incluso
Mitsubishi SE-CPU2 PCB Control Board for FR-SE Spindle Drive BN624A471G54
SKU: SE-CPU2
The Mitsubishi BN624A471G54 (SE-CPU2) is a printed circuit board and CPU control card used in Mitsubishi FR-SE spindle drive systems. It is listed as a PC board and spindle drive board for FREQROL spindle drive and CNC machine applications. Within the FR-SE drive, the SE-CPU card works with the SE-IO card, and the FR-SE maintenance manual refers to LEDs and test points on the SE-CPU card for setup, waveform checks, and troubleshooting. The board is used in CNC machine tools and spindle drive service where the SE-CPU2 control PCB is required. The model designation is SE-CPU2, revision B is referenced, and the associated Mitsubishi part number is BN624A471G54. Typical use is replacement of the control-board function in Mitsubishi FR-SE and FREQROL spindle drive electronics for CNC systems.
Mitsubishi SE-IO1 Spindle Drive Control Board for FREQROL FR-SE
SKU: SE-IO1
The Mitsubishi SE-IO1 (SE-IO1) is a control board used in Mitsubishi FREQROL FR-SE spindle drives. It serves as the drive's interface to the CNC control, carrying speed-command signals, discrete enable, forward, reverse and fault-reset inputs, and returning drive-OK, zero-speed and at-speed outputs. The speed command can be an analog ±10 V signal or a digital word, depending on the FR-SE configuration. The board is found in legacy FR-SE spindle drive installations, including Mazak QT10 turning centers with Mazatrol T2 controls. In service, a faulty or unseated SE-IO1 can contribute to no-LED or no-power symptoms, spindle-controller alarms and signal faults between the drive and control. Its edge connector and Honda connectors should be inspected for oxidized contacts, loose seating and damaged wiring during troubleshooting. Typical applications include repair, bench testing and replacement of the spindle-drive control section on CNC machining centers, turning centers and grinding machines.
Mitsubishi SF-CA PCB Control/Converter Board for FR-SF Spindle Drives
SKU: SF-CA
The Mitsubishi SF-CA (SF-CA) is a printed circuit board and control/converter card used in Mitsubishi FR-SF spindle drive systems, including MELDAS-family CNC machining centers. It mounts within the FR-SF modular spindle amplifier and mates with the SF-PW power supply through a multi-pin card-edge connector. Through this interface, the board carries high-current gate-drive return paths, DC bus voltage sensing for under-voltage and over-voltage protection, IGBT desaturation fault signals, and auxiliary logic rails. The SF-CA converter section is associated with the drive's regenerative front end and phase-loss detection, including input-phase alarm handling. The board is used in troubleshooting and repair of FR-SF spindle drives, where a missing LED display or intermittent spindle alarms can point to the SF-CA card or its card-edge connection. Current product information flags the item as obsolete and notes SF-CA/SF-CAA (PCB-00008) as a use/transfer reference. It is intended for maintenance, repair, and replacement of Mitsubishi FR-SF drive assemblies rather than for standalone use.
Mitsubishi SF-JRVB Vertical Flange-Mounted Three-Phase Brake Motor for Mixers and Machinery
SKU: SF-JRVB
The Mitsubishi SF-JRVB (SF-JRVB) is a three-phase induction brake motor from the SF-JRVB series, built in a vertical, flange-mounted configuration for mixers and general machine drives. It combines a fully enclosed fan-cooled induction motor with a non-excitation spring-applied brake. Across the series, braking torque spans 2 to 150 N·m and the mechanical brake life is rated at 2 million cycles. Standard motor voltages are 200/200/220 V at 50/60/60 Hz, and the motor protection is IP44 with IP20 at the brake; insulation class is F. The series is designed for ambient temperatures of -20 to 40 °C, humidity up to 95% RH and altitudes up to 1000 m. Available outputs range from 1/4 to 10 hp, with three lead wires on ratings up to 3.7 kW and six lead wires from 5.5 kW; frames up to 132 use a terminal block, while 160-frame units use lugs. The supplied product data lists a 100L frame, 1.5 kW, 1720 rpm and 220 V three-phase rating. Typical uses include mixers and machinery that require flange mounting, high torque and smooth speed.
Mitsubishi SF-PR-CN 0.75 kW 4-Pole Premium Efficiency Three-Phase Induction Motor for China SF-PR-CN-0.75KW-4P-380V-50HZ
SKU: SF-PR-CN-0.75KW-4P-380V-50HZ
The Mitsubishi SF-PR-CN-0.75KW-4P-380V-50HZ (SF-PR-CN) is a 0.75 kW, 4-pole, 380 V 50 Hz three-phase induction motor from the SF-PR Super Line premium-efficiency series. It is the SF-PR-CN variant listed for China CCC certification at the 0.75 kW/4-pole rating. The motor is intended for continuous-duty industrial drive applications and uses a totally enclosed fan-cooled frame; the 0.75 kW four-pole rating is built on frame size 80M. The SF-PR series is designed to IE3 premium efficiency, helping reduce energy consumption compared with older standard motors while maintaining mounting compatibility with conventional three-phase motors. Standard SF-PR series data includes an S1 continuous rating and IP44 protection, with IP55 dust- and waterproof versions available. Ambient conditions are -30 to 40 °C, up to 1000 m altitude. The motor can be driven by a Mitsubishi inverter, and the series is noted for constant-torque operation in the low-speed range. Typical uses include pumps, fans, conveyors, compressors, and other general industrial machinery where reliable three-phase power and energy savings are required. This listing is for the 380 V 50 Hz, 4-pole, 0.75 kW SF-PR-CN motor.
Mitsubishi SF-PW Logic Power Supply Unit for FR-SF Series Spindle Drives
SKU: SF-PW
The Mitsubishi SF-PW (SF-PW) is a logic power supply unit intended for FR-SF series spindle drives in CNC systems. It is the power supply assembly used for the logic power path in the spindle drive system, supporting the control electronics rather than the main motor power stage. The unit also appears under the SFPW abbreviation in listings and service references, and it is identified as discontinued by the manufacturer. For replacement planning, the current product record directs users to the SF-PW30 (U543) as the successor or transfer reference. The SF-PW is associated with Mitsubishi FR-SF spindle drive installations, making it relevant to maintenance and repair of older CNC spindle systems. Its role as a logic supply makes it a service part for drive cabinets where the control section requires a dedicated power source. Available evidence does not confirm output voltage, connector type, enclosure dimensions, or net weight, so those specifications should be verified against the machine documentation before ordering. This listing covers the SF-PW power supply unit and is intended for repair, replacement, and spare-parts identification.
Mitsubishi SF-PW20 Power Supply Unit for CNC Machinery
SKU: SF-PW20
The Mitsubishi SF-PW20 is a power supply unit for the electronic components of computer numerical control (CNC) machinery. It is built in a partially enclosed housing with a status indicator, so the operating state of the supply can be checked directly on the module. The unit is listed as equivalent to the BKO-NC6452 power supply reference and serves as a maintenance replacement in Mitsubishi CNC control cabinets and machine tool electronics. The part is obsolete: Mitsubishi recommends using or transferring to the SF-PW30 (U543), the successor power supply, so existing SF-PW20 units are mainly relevant for repairs, spares stock and machines that still run the original configuration. Typical use is the replacement of a failed or aging logic power supply in CNC equipment, during service work, or when keeping a legacy machine tool operational. Verify the replacement path to SF-PW30 before ordering where a new installation is planned.
Mitsubishi SF-PWH Power Supply Unit for FREQROL FR-SF Spindle Drives
SKU: SF-PWH
The Mitsubishi SF-PWH is a power supply unit for Mitsubishi FREQROL FR-SF spindle drive systems. It is used in FR-SF spindle controllers, including FR-SF-2 and FR-SF-4 series units, to supply voltage to the spindle drive section. The module accepts a single-phase 200-230 VAC, 50/60 Hz input and has a nominal 230 VAC rating. Its net weight is approximately 1.23 kg. Typical applications include CNC machine tools and production equipment that use Mitsubishi FREQROL spindle controllers, particularly repair cases where a faulty SF-PW or SF-PWH supply is linked to a dark seven-segment display. The SF-PWH is listed as obsolete, with SF-PWH30 (U710-1) given as the transfer reference, so the replacement route should be verified before ordering. Service documentation also identifies the SF-PWH as a Yamabishi power unit used with Mitsubishi FREQROL spindle controllers. The unit is also referenced as SFPWH. It is intended for maintenance, repair and replacement of Mitsubishi spindle drive power supply assemblies.
Mitsubishi SF-TL PCB Circuit Board for FR-SF Spindle Drive BN624A961G52A
SKU: SF-TL
The Mitsubishi BN624A961G52A (SF-TL) is a printed circuit board assembly and option card designed for Mitsubishi FREQROL-SF spindle drives and M300 series CNC systems. It is identified in service documentation as the SF-TL card, with part number BN624A961G52A and the related designation BN624A961G52. In the drive, the board supports spindle functions such as high-speed synchronous tapping and spindle orientation, including C-axis control using a magnetic sensor. The card communicates with the NC through cable connectors CN1A and CN1B, and it includes a rotary switch CS1 whose setting must match the required configuration. Because the SF-TL board is part of the spindle control path, correct seating of the card and secure connection of its cable connectors are important during installation and troubleshooting. It is used in CNC machining and spindle applications where coordinated spindle positioning, orientation, or synchronous tapping is required.
Mitsubishi SG-2P-164M-DL-CC Outdoor Fiber Optic Patch Cable for Mitsubishi PLCs
SKU: SG-2P-164M-DL-CC
The Mitsubishi SG-2P-164M-DL-CC is an outdoor fiber optic patch cable and cordset for Mitsubishi PLC systems and related programmable controller accessories. It provides a 164 m (538 ft) fiber optic connection and carries the manufacturer order code SG-2P-164M-DL-CC, which is equivalent to SG2P164MDLCC. The cable sits within Mitsubishi Electric's PLC accessory range, where it is used to connect compatible control equipment when an outdoor fiber optic patch lead is required. Its 164 m length supports installations that need a longer fiber run between PLC cabinets and associated control or network equipment. Mitsubishi Electric lists the product with commercialized status. Key supported data includes the outdoor fiber optic patch cable/cordset function, the 164 m / 538 ft length, and the PLC accessory classification. Typical uses include Mitsubishi PLC installations, control-system upgrades, and replacement of an existing 164 m outdoor fiber link specified as SG-2P-164M-DL-CC or SG2P164MDLCC.
Mitsubishi SG-2P-212M-DL-CC Outdoor Fiber Optic Patch Cable for PLC Systems 212 m
SKU: SG-2P-212M-DL-CC
The Mitsubishi SG-2P-212M-DL-CC (SG-2P-212M-DL-CC) is an outdoor fiber optic patch cable/cordset from the Mitsubishi Electric range of programmable logic controller components and various accessories. It is supplied as a 212 m (695 ft) cable assembly for use with Mitsubishi Electric PLC systems and related control equipment, where a long optical patch connection is required. The product is identified by order code SG-2P-212M-DL-CC and is listed as equivalent to SG2P212MDLCC. The available data confirms its cable function, outdoor fiber optic patch cable/cordset type, and 212 m / 695 ft length; connector style, fiber type, jacket material and environmental ratings are not stated in the available information and should be checked against the manufacturer's datasheet for the specific installation. Typical applications are Mitsubishi Electric PLC and MELSEC control systems, network cabinets and industrial control panels that use compatible fiber optic connections. The manufacturer lists the item status as commercialized. Because system compatibility depends on the controller and network module, verify the part number against the equipment before ordering.
Mitsubishi SG-2P-311M-DL-CC Outdoor Fiber Optic Patch Cable 311 m for PLCs
SKU: SG-2P-311M-DL-CC
The Mitsubishi SG-2P-311M-DL-CC (SG-2P-311M-DL-CC) is an outdoor fiber optic patch cable / cordset listed for Mitsubishi Electric PLC accessory use. It has a 311 m (1,020 ft) length and is identified as equivalent to the SG2P311MDLCC order code. The cable is cataloged in the Mitsubishi PLCs and various accessories family, so it is intended for fiber-optic cabling in PLC and accessory installations where a long outdoor patch lead is needed. Its manufacturer product status is shown as commercialized. Available product data does not list connector type, fiber mode, jacket material, or environmental ratings, so these details should be confirmed against the cable marking or Mitsubishi documentation before ordering. The item is supplied under SKU SG-2P-311M-DL-CC and serves as a long-length outdoor fiber-optic cable accessory for Mitsubishi PLC applications.
Mitsubishi SG-2P-365M-DL-CC Outdoor Fiber Optic Patch Cable Set 365 m for SG Series
SKU: SG-2P-365M-DL-CC
The Mitsubishi SG-2P-365M-DL-CC is an outdoor fiber optic patch cable set with a 365 m (1,197 ft) length, supplied as a complete cable set for long-distance optical connections in Mitsubishi equipment installations. Its outdoor designation makes it suitable for routing between cabinets, machines, or control points where an extended fiber-optic link is required. The assembly is identified as equivalent to SG2P365MDLCC, helping confirm compatibility when replacing or specifying the original Mitsubishi cable set. It is intended for Mitsubishi SG-series machines and systems that use fiber-optic patch cabling for signal transmission and interconnection. Because the cable is supplied as a set, it supports planned replacement and installation work where the complete 365-meter run must be renewed. No connector type, fiber mode, jacket material, or environmental rating beyond the outdoor designation is stated in the available product data; confirm those details against the machine documentation before ordering. Typical use is fixed outdoor or inter-cabinet fiber-optic routing in industrial equipment, control systems, and Mitsubishi SG-series installations.
Mitsubishi SG-2P-561M-DL-CC Fiber Optic Cable
SKU: SG-2P-561M-DL-CC
Cavo patch in fibra ottica per esterni / set di cavi - MITSUBISHI ELECTRIC - lunghezza 561 metri / 1.840 piedi - equivalente a SG2P561MDLCC
Mitsubishi SG-2P-600M-DL-CF Fiber Optic Cable
SKU: SG-2P-600M-DL-CF
Cavo patch in fibra ottica per esterni / set di cavi - MITSUBISHI ELECTRIC - lunghezza 600 metri / 1.968 piedi - equivalente a SG2P600MDLCF
Mitsubishi SG-2P-916M-DL-CC Fiber Optic Patch Cable
SKU: SG-2P-916M-DL-CC
Cavo patch in fibra ottica per esterni / set di cavi - MITSUBISHI ELECTRIC - lunghezza 916 metri / 3.005 piedi - equivalente a SG2P916MDLCC
Mitsubishi SH21-0.35M Cable
SKU: SH21-0.35M
Cavo di alimentazione e comunicazione / set di cavi - per unità a Controllo Numerico Computerizzato (CNC) - MITSUBISHI ELECTRIC - lunghezza 35 centimetri / 13 pollici - equivalente a SH210.35M
Mitsubishi SH21-1.0M CNC Cable (1m)
SKU: SH21-1.0M
Cavo di alimentazione e comunicazione / set di cavi - per unità a Controllo Numerico Computerizzato (CNC) - MITSUBISHI ELECTRIC - lunghezza 1 metro / 3 piedi - equivalente a SH211.0M
Mitsubishi SJ-4-V11-18T(F) Spindle Motor
SKU: SJ-4-V11-18T(F)
Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 11 chilowatt (kW) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 47,7 Nm nominali - velocità di rotazione nominale 1.500 giri al minuto (rpm) - montaggio a flangia 204x204 millimetri - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
Mitsubishi SJ-4-V11-18WT(M) Spindle Motor
SKU: SJ-4-V11-18WT(M)
Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - uscita costante ad ampio raggio - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 5.500 Watt (W) / 5,5 chilowatt (kW) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 47,7 Nm nominali - velocità di rotazione nominale 1.500 giri al minuto (rpm) - taglia flangia 204x204 millimetri con montaggio a piedini - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
Mitsubishi SJ-4-V11-21WT(F) Spindle Motor
SKU: SJ-4-V11-21WT(F)
#fuori produzione - Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - uscita costante ad ampio raggio - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 7.500 Watt (W) / 7,5 chilowatt (kW) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 70 Nm nominali - velocità di rotazione nominale 750 giri al minuto (rpm) - montaggio a flangia 250x250 millimetri - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
Mitsubishi SJ-4-V11-21WT(M) Spindle Motor
SKU: SJ-4-V11-21WT(M)
#fuori produzione - Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - uscita costante ad ampio raggio - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 7.500 Watt (W) / 7,5 chilowatt (kW) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 70 Nm nominali - velocità di rotazione nominale 750 giri al minuto (rpm) - taglia flangia 250x250 millimetri con montaggio a piedini - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
Mitsubishi SJ-4-V11-22ZT(F) Spindle Motor
SKU: SJ-4-V11-22ZT(F)
Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - cuscinetto ad alta velocità - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 5.500 Watt (W) / 5,5 chilowatt (kW) (servizio continuo) / 7,5 chilowatt (kW) (per massimo 30 minuti) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 35 Nm nominali - velocità di rotazione nominale 1.500 giri al minuto (rpm) - montaggio a flangia 204x204 millimetri - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
Mitsubishi SJ-4-V11-22ZT(M) Spindle Motor
SKU: SJ-4-V11-22ZT(M)
Motore mandrino con albero dritto + codificatore di retroazione assoluto integrato tipo 2 - cuscinetto ad alta velocità - MITSUBISHI ELECTRIC (serie SJ-V) - uscita nominale 5.500 Watt (W) / 5,5 chilowatt (kW) (servizio continuo) / 7,5 chilowatt (kW) (per massimo 30 minuti) - classe tensione di alimentazione 400 Volt in corrente alternata (Vac) - coppia nominale 35 Nm nominali - velocità di rotazione nominale 1.500 giri al minuto (rpm) - taglia flangia 204x204 millimetri con montaggio a piedini - grado di protezione (IP) 44 - tarato per temperatura ambiente da 0 a +40 gradi Celsius
SG-2P-912M-DL-CC MITSUBISHI
SKU: SG-2P-912M-DL-CC
Cavo patch in fibra ottica per esterni / set di cavi - MITSUBISHI ELECTRIC - lunghezza 912 metri / 2.992 piedi - equivalente a SG2P912MDLCC
SG-2P-991M-DL-CC MITSUBISHI
SKU: SG-2P-991M-DL-CC
Cavo patch in fibra ottica per esterni / set di cavi - MITSUBISHI ELECTRIC - lunghezza 991 metri / 3.251 piedi - equivalente a SG2P991MDLCC
SHTA240-05SVRFS MITSUBISHI
SKU: SHTA240-05SVRFS
Sganciatore a lancio di corrente. 100-240 Volt in corrente alternata (Vac), montaggio lato destro 4 poli, per W75, 90, 105. Morsettiera.
SHTA550-05SVRFS MITSUBISHI
SKU: SHTA550-05SVRFS
Sganciatore a lancio di corrente. 380-550 Volt in corrente alternata (Vac), montaggio lato destro 4 poli, per W75, 90, 105. Morsettiera.
SHTD024-10SWRFS MITSUBISHI
SKU: SHTD024-10SWRFS
Sganciatore a lancio di corrente. 24 Volt in corrente continua (Vdc), Morsettiera, 4 poli, NF1000-SEW, NF1250-SEW, NF1600-SEW